Restore maximum power and OEM-level performance. For premium GDI injector cleaning and high pressure testing, go with Redline Injectors.
GDI Injector Cleaning Service

What to Expect - Direct Injector Service
Whether your Gasoline Direct injectors are dirty or clogged, our premium injector cleaning and flow testing service delivers manufacturer-level static and dynamic testing on state of the art precision computer-controlled benches and includes all required replacement parts, O-rings, seals etc.
- If we determine the injectors is bad electrically or mechanically before we begin cleaning and testing we will call you, let you know and refund you the service cost of that injector.
- Using computer-controlled, high-pressure flow OEM test plans that are specific to each injectors part number, we provide a valid, data-driven assessment of the injector’s condition and performance across 8-10 dimensions.
- Unlike port injectors, GDI injectors are cleaned first and then tested; they are not pre-tested.

GDI Injector Cleaning
- We consistently achieve better GDI Injector cleaning results thanks to our unique cleaning procedures. It’s not uncommon for injectors that undergo traditional cleaning methods; including non-leaking units; to still perform poorly on testing. However, employing our proprietary chemicals with our air-injected cleaning process and POWERFLUSH treatment, those same injectors often snap right back into the proper flow corridors. It does not happen every time, but it does happen far more frequently than not.
- Injectors can still occasionally fail even after our extensive cleaning procedures, typically due to weak or damaged coils, internal wear or weakened return springs. If this occurs, you can be confident it is not the result of inadequate cleaning procedures.

Direct Injectors Testing Pressure Matters
Gasoline Direct injectors (GDI) operate at extremely high pressures of 500-2300 PSI. Our Carbon Zapp GDR-X test bench, featuring computer-controlled fluid temperature management executes manufacturer-specific injector flow test plans and supports pressures up to 5,000 PSI for GDI injector testing. To help ensure success, we employ proprietary cleaning procedures.
- Each injector is evaluated according to manufacturer test plans against the injectors part number to ensure OEM-level accuracy with up to 10 precision computer controlled tests per injector on oer our specialized GDI test bench.
- Without the ability to replicate correct pressure, actuation, sealing, and spray conditions, any flow or leak results are invalid. Meaningful, accurate results requires specialized equipment designed specifically for direct injectors, not eyeballs and looking at the spray pattern at 90 psi on a port injector machine.
- Port injection test machines provide no meaningful evidence of injector flow performance and can lead to false diagnoses, incorrectly identifying faulty injectors as good, click the button to see an example in the video.

Common GDI Injector Problems
- Gasoline Direct Injection (GDI) systems commonly suffer from several interrelated issues due to their high pressures and injector placement.
- Carbon buildup at the injector tip allows combustion byproducts to accumulate inside and outside the injector tip, restricting fuel flow at the pintle.
- GDI injectors themselves are prone to internal clogging and inconsistent fuel delivery as they operate in extreme heat and pressure, leading to poor atomization, misfires, and rough running.
- Injector seal leaks, particularly at the combustion chamber seal, can allow compression and combustion gases to escape, damaging injectors and causing hard starts or fuel odor.
- Together, these conditions increase the likelihood of excessive engine knock or pre-ignition, which can result in loss of power and, in severe cases, serious engine damage.

Proper Injector Numbering
- Optionally, mark each injector with its cylinder number using a Sharpie and masking tape tag or something similar. We will tag the injectors with plastic tags using your provided number.
- Writing on the injector with a sharpie will rub off during shipping.
- Etching the numbers is fine as long as they are not obscure and hard to find, we are not responsible if we do not not find your numbering.
- But honestly it is just easier and far more reliable to use a strip of painters tape with a sharpie number.

How to Read Direct Injector Test Reports
These injectors generate performance reports with unique terminology. To help make sense of them, we created a guide to understanding GDI flow test reports. There will be 1 report per numbered injector and are electronically delivered to your email.
Key Topics For GDI Injectors
How to Properly Test GDI & Piezo Injectors
Can You Test GDI/Piezo Injectors On a Port Injection Machine?
How are Piezoelectric and GDI Injectors different?
How often should I have fuel injectors cleaned and why?
What are differences between Port and GDI Injectors?
Shipping and Service FAQs
Service Related Questions
Yes, we have a 2 injector minimum.
Absolutely! Rest assured that we will take care of removing the injectors for you for (typically GDI and side feed) and invoice you for a bench fee of $10 per rail to do the work as problems can often arise. However, it’s important to note that we cannot be held responsible for any potential damage that may occur during the removal process. To ensure a smooth experience, we recommend that you personally remove the injectors from the rail.
To avoid any issues with shipping service secure them in plastic and tape them to prevent leaks.
For your convenience, side feed injectors will be re-installed in the fuel rails, top feed and GDI injectors will be packaged separately. GDI Injector clips are fairly easy to remove, you should not have no any issues, but if yours are tricky to remove we will can do it if you wish.
- Service prices and options are posted in store per item type as well as on the pricing page. Service Pricing
- Please check the Injector id injectors page on the menu if your unsure what you have. Injector ID
Turn around times are stated on the Home page.
We always replace filters, O-rings, seals, spacers, grommets etc. whenever they are available for the injector, this includes side feed injectors as opposed to cleaning them while still on the injector as most places do. They become fragile over time, why take a risk.
In fact we replace everything that is replicable.
Shipping Related Questions
For local drop/pick up service check the “Local Drop-Off” box on the order form.
Once order is places, email us at [email protected] for drop off instructions.
- Shipping insurance up to $100 is automatically provided.
- To add Shipping additional Insurance, please select amount coverage you’d like using the “Shipping Insurance” line item before checkout.
- Additional shipping insurance is calculated for you based on $1.60 per $100 of declared value.
- Please insure items based on their actual replacement value, extra insurance above the value will accomplish nothing, claims are on shipment value, not amount of insurance bought.
- Insurance applies only to the item we’re returning to you.
Yes we will email the contact on the “Order receipt” that we get a copy of when you place your order. Include your Name on a card or paper inside the shipment box as the shipping label sometimes gets obscured.
Include your Name on a card or paper inside the shipment box as the shipping label sometimes gets obscured.
We accept shipments from UPS, USPS, Fedex or DHL to following address 7 days a week.
Sending UPS is the optimal choice within the US, however.
Redline Injectors
3036 State Route 35 #227
Hazlet, NJ 07730
Include your Name on a card or paper inside the shipment box as the shipping label sometimes gets obscured.
When preparing the injectors for shipping, it is strongly advised to place them inside a regular zip lock bag first. This will help to keep the fuel smell contained. It is important to avoid any damage during transit, so make sure not to simply toss the bag into a box without any additional packing material. This is particularly crucial for the pintle end.
It is not recommended to ship the injectors in a bubble envelope. Optimal protection can be achieved by using a box with some padding or a bubble envelope in a box. The small flat rate box from the Post Office may be good budget-friendly option for smaller injectors.
Send the injectors with all O-rings and related components, either installed on the injectors or placed together in a bag.
